tubo láser de co2 de diez alturas 40w 700 mm d50 mm, para cortadora láser máquina cortadora de grabado láser ac110v, cables preconectados con revestimiento mayor vida útil
- Marca:
ten-high
- Código producto: B00BKWOS1E
- Disponibilidad: Traemos a pedido, tiempo de 15 a 25 dias.
-
$CLP 368.740
TÉRMINOS Y CONDICIONES
------------------------------------------
- El producto se trae a pedido, en un transcurso de 15 a 25 dias, si alguna restriccion de un ente gubernamental o de salud publica cambia o restringe vuelos, los pedidos pueden demorar mas tiempo.- Precios pueden cambiar previo aviso. Depende de precio con proveedores o existencia.
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken.
- Productos importados de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.
- Power: 40 Watt, Length: 700mm, Diameter: 50mm. This CO2 Laser Tube has an inlet and outlet for water cooling and wire connections for the anode and cathode sides of the tube. For ease of installation, the high voltage port and low voltage port have been connected in advance.
- Professional water cooling and hermetic CO2 glass laser tube, mainly used for laser engraving machine, laser marking machine, laser engraving machine, laser cutting machine, is Replacement parts for laser machine, and can be carved and cut acrylic, cloth, leather, bamboo, wood, engraving, etc. It is excellent in laser spot mode, has strong laser energy, and a long service life.
- Each tube is tested for quality before it is sent out, with a voltage test performed and a read-out of performance at different wattages. It is important to note that while you may achieve higher performance at higher wattage, it can also shorten the life of the tube. Laser tubes are consumable products much like light bulbs are. They have a rated life span. The 40W tube's lifespan is rated at 1500H-2500H(under normal use).
- The laser tube after generally work 3-4 hours should to pause for about 30 minutes, This laser tube should be used and placed under the normal room temperature in the cold weather (To prevent the cooling water frozen as the weather getting colder). Please make sure your machine has enough installation space, like the diameter and length, all should be a little bigger than laser tube's size.
Introduction Model:CO2-TUBE-40W-70CM Output Power:40W Wavelength:10600nm Working Voltage:15KV (Trigging Voltage=22KV) Working Current:15mA Divergence:1.95(beam diameter) Dimensions:Length 700mm Input voltage: AC 220V+30 or AC 110V+20 (to be specified when placing order). Maximum output voltage:DC25KV (40W;50W) / DC28KV (60W) / DC35KV (80W) Maximum output current: DC20mA (40W;50W)/ DC23mA (60W) / DC28mA (80W) Isolation Withstand voltage: Input-output, input-enclosure: AC2000V-10mA-60s; negative pole of output connected to enclosure. Protection: with well-grounded enclosure, output circuit of power supply can be open for short time (but arc between positive pole and enclosure should be avoided). Response time (from time of input being available to the output current being up to nominal value)<1ms TTL voltage level control: effective voltage level can be high or low through setting. Protection switch: for detection of cooling water, to protect laser device; or activate with enclosure is opened. Laser power adjustment: (1) by adjusting the output current of power supply through resistor; (2) through PWM control (magnitude being TTL voltage level). Environmental requirements: temperature (-10 to 40centidegree), relative humidity<85%.
- Professional water cooling and hermetic CO2 glass laser tube, mainly used for laser engraving machine, laser marking machine, laser engraving machine, laser cutting machine, is Replacement parts for laser machine, and can be carved and cut acrylic, cloth, leather, bamboo, wood, engraving, etc. It is excellent in laser spot mode, has strong laser energy, and a long service life.
- Each tube is tested for quality before it is sent out, with a voltage test performed and a read-out of performance at different wattages. It is important to note that while you may achieve higher performance at higher wattage, it can also shorten the life of the tube. Laser tubes are consumable products much like light bulbs are. They have a rated life span. The 40W tube's lifespan is rated at 1500H-2500H(under normal use).
- The laser tube after generally work 3-4 hours should to pause for about 30 minutes, This laser tube should be used and placed under the normal room temperature in the cold weather (To prevent the cooling water frozen as the weather getting colder). Please make sure your machine has enough installation space, like the diameter and length, all should be a little bigger than laser tube's size.
Introduction Model:CO2-TUBE-40W-70CM Output Power:40W Wavelength:10600nm Working Voltage:15KV (Trigging Voltage=22KV) Working Current:15mA Divergence:1.95(beam diameter) Dimensions:Length 700mm Input voltage: AC 220V+30 or AC 110V+20 (to be specified when placing order). Maximum output voltage:DC25KV (40W;50W) / DC28KV (60W) / DC35KV (80W) Maximum output current: DC20mA (40W;50W)/ DC23mA (60W) / DC28mA (80W) Isolation Withstand voltage: Input-output, input-enclosure: AC2000V-10mA-60s; negative pole of output connected to enclosure. Protection: with well-grounded enclosure, output circuit of power supply can be open for short time (but arc between positive pole and enclosure should be avoided). Response time (from time of input being available to the output current being up to nominal value)<1ms TTL voltage level control: effective voltage level can be high or low through setting. Protection switch: for detection of cooling water, to protect laser device; or activate with enclosure is opened. Laser power adjustment: (1) by adjusting the output current of power supply through resistor; (2) through PWM control (magnitude being TTL voltage level). Environmental requirements: temperature (-10 to 40centidegree), relative humidity<85%.
